Standard Equipment Features
Energy-saving performance – a heavy blanket of high-density fiberglass insulation is used to meet the demanding ASHRAE 90.1b 1992 standard for minimizing heat loss. This requirement, allowing a maximum 4 watts per square foot of tank surface energy loss, offers big savings and operating efficiency.
Magnetic contactors with immersion thermostats – 120 volt control circuit with built in transformer. Elements are thermostatically controlled in 54KW (max) increments.
Low watt density Incoloy elements – Incoloy elements are used by Bradford White because of their many superior characteristics to copper-sheathed elements in rigorous water heating applications. This tough alloy
successfully resists the effects of prolonged high operating temperatures, hard water, acids, corrosion, and thermal shock. Their nominally higher initial cost is more than offset by much longer life expectancies and reduced service and replacement labor costs. Incoloy elements are designed to “burn in air” to prevent failures caused by water void.
Internal fusing – all elements and circuits are fused in
48 amp. increments, providing complete electrical protection. Cartridge type fuses are rated at 200,000 ampere interrupting capacity.
Glass-lined tank – vitreous glass is applied to the inside surface of the steel tank and fired to 1600°F. (All models are constructed in accordance with the ASME code and approved for 125 PSI working pressure.)
Built-in safety drain pan (square only) – all Brute Heater models feature a built-in, sealed drain pan system...complete with a 3/4" drain connection. This assists in protecting against water damage from tank or component leakage. Not available on round models.
Magnesium tank saver – provides anodic protection against corrosion of the tank due to electrolysis.
Galvanized jacket – the heavy 16-gauge steel jacket is galvanized on both sides and beautifully finished in durable acrylic enamel. This combines attractive appearance with maximum protection.
Full-length hinged door with key lock –quality requires full-length hinged doors for ease of inspection and maintenance. Key Door Lock provides additional safety and security at no extra charge.
Temperature and pressure relief valve –factory provided ASME rated relief valve protects against excessive temperature and/or pressure buildup within the tank.
Terminal block connections – easy and safe wiring connections are made possible by factory installed terminal blocks.
180°F temperature operation – every Brute Heater is approved for 180°F. operation for sanitizing and other high-temperature requirements.
Hand hole cleanout – provides easy access to the heater interior for inspection and cleaning.
Channel iron skid base - available for 250 gallons and larger.
UL listed - all models are listed by Underwriters Laboratories, Inc. as commercial electric water heaters...your assurance of competent design and proper testing.
Three-year limited warranty - provides warranty protection against tank failure resulting from defects in
material and workmanship.
Optional Equipment Features:
Low water cut off - prevents energizing of the heater when not filled with water or upon low water condition.
Pilot lights - monitor on/off cycle for each contactor.
Manual limiting switches - with indicating lights ?permits manually limiting heating input by switching off
current to each contactor.
Solid state modulating control (electronic sequencer) - modulates power input and balances load to demand. Contactors are staged automatically and sequentially to equalize element usage. Unit reprograms to off position on power failure. (Available only for 36 KW or
higher)
Alarm bell - warns of various control failures.
Shunt trip disconnect - provides maximum protection by interrupting all power to the system in the event of a control sensed malfunction or overcurrent. (Separate mounting).
Low or high pressure switch - turns off control circuit when water pressure drops below a set minimum, or
above a set maximum.
Time clock - to control off/on cycles of the heater as programmed by the owner or electric utility requirements. (Separate mounting) (7 day or 24 hour)
Safety door interlock - prevents opening of access door while heater is energized.
Temperature and pressure gauges - jacket mounted for convenient viewing.
Man hole (square only) - provides means to easily remove sediment from the heater; optional on 250 to 400 gallon models; standard on 500 gallons and larger. Not available on round models.
Additional manual reset hi limit - requires heater to be manually reset upon over-temperature condition.
Lifting Lugs - (not available on vertical round models). Standard on 600 gallons and larger.
Working pressure - 150 PSI or 160 PSI ASME construction.
†Separate mounting - Field Installed.